CCSD3ZF0000100000001NJPL3IF0PDS200000001 = SFDU_LABEL RECORD_TYPE = FIXED_LENGTH RECORD_BYTES = 80 SPACECRAFT_NAME = MAGELLAN TARGET_NAME = VENUS OBJECT = TEXT PUBLICATION_DATE = 1993-10-10 NOTE = "COMMENTS ON MAGELLAN MIDR CD-ROMS" END_OBJECT END COMMENTS ON MAGELLAN MIDR CD-ROMS 1. Purpose of This Document This document is a cumulative summary of comments concerning the Magellan MIDR data set published on CD-ROMs. It contains comments on all the MIDR CD-ROMs published so far. Comments include information of interest to users of the data and notes about any known errors on the CD-ROMs. 2. General Comments 2.1 Normalization of Data Note that the eight-bit digital numbers (DN's) for each MIDR pixel on the CD-ROM's were computed by taking the estimated backscatter cross sections, dividing the values by the value for the Muhleman scattering law at the same incidence angles, converting to decibels, and scaling to bytes. The Muhleman Law has the following expression: sigma naught = A cos(i) / (sin(i) + B cos(i)) ** 3 Values for A and B were meant to be 0.0188 and 0.111, respectively Through an error, the A value used for the Muhleman Law estimate was 0.0118. As a result of this mistake, the pixel values are systematically about 10 DN (2 dB) greater than they should be according to the planned algorithm. Also, because of an indexing error, the incidence angles used in the above equation were 0.5 degrees lower than the actual angles. 2.2 VICAR2 Labels of Browse Images The browse versions of MIDR's were created by reducing the original 7168 by 8192 MIDR by a factor of 8. The VICAR2 labels for the browse images do not accurately reflect the size reduction, in that parameters PROJSAMP, PIXSIZ, and SPECLINE still pertain to the original MIDR size. 2.3 Data Feathering MIDR products on the CD-ROM's, in some cases, have had a feathering algorithm applied to suppress banding due to BIDR differences. The file CONTENTS.TAB includes a column (column no. 31) that specifies whether or not feathering has been applied. A "C" in this column indicates correction by feathering, while an "R" means not feathered. 3. Comments on volume MG_0001, version 2 3.1 Difference between MG_0001 file structure and Standard file structure The files MCUMDIR and CONTENTS are in the root directory of MG_0001. They are in subdirectory INDEX of MG_0002 and subsequent CD's. In addition, MG_0001 has a label file PMIDRDS.LBL in the LABEL directory. This file is replaced by NPMIDRDS.LBL and SPMIDRDS.LBL in the LABEL subdirectory of MG_0002 and subsequent CD's. For MG_0002 and subsequent CD's, a number of other label and text files (including AAREADME.TXT) have been updated to reflect these and a few other minor changes. 3.2 Difference between Standard and Engineering F-MIDR's The ten F-MIDR's on this CD-ROM are not standard products; rather, they are engineering test products generated before delivery of operational software. There are three primary differences between Engineering F-MIDR's and standard F-MIDR's. First, Engineering F-MIDR's consist of 20 orbits whereas standard F-MIDR's contain 24 orbits. Second, Engineering F-MIDR's are not necessarily complete on the trailing edge and may contain missing orbits within the body of the mosaic that have since been processed. The gap at the trailing edge of some of the F-MIDR's is a start of mapping gap and is present because processing began with orbit 376. Gaps in the bodies of the F-MIDR's are present because the Image Data Processing Team (IDPT) was instructed not to wait until all orbits had completed the processing queue. Therefore, orbits that the SAR Data Processing Team (SDPT) had trouble processing appear as gaps in the Engineering F-MIDR's even though the orbit has now been processed. 3.3 Error in VICAR2 Keyword PROJSAMP This CD-ROM has an error in the VICAR2 labels for the mosaicked framelets. Specifically, the value for PROJSAMP does not vary from framelet to framelet. 3.4 VICAR2 Labels of MIDR Framelets Some of the MIDR framelet files have a VICAR2 label embedded at the end of the file, in addition to the normal VICAR2 label at the beginning of the file. This extra label is not documented in the PDS detached label. 3.5 Product ID in VICAR2 Label In two of the data subdirectories, the product ID given in the VICAR2 embedded labels is not correct. Specifically, the VICAR2 label has an N for north latitude instead of an S for south latitude. The correct IDs are as follows: directory product ID in VICAR2 labels correct product ID --------- --------------------------- ------------------ [F05S335] F-MIDR.05N335 F-MIDR.05S335 [F40S342] F-MIDR.40N342 F-MIDR.40S342 3.6 Error in BROWSE.LBL Files The PDS label files for the browse images on this CD-ROM (all named BROWSE.LBL) contain incorrect entries in the IMAGE object. The keyword LINES, which shows a value of 1024, should have the value 896. The keyword LINE_SAMPLES, which shows a value of 896, should have the value 1024. 4. Comments on Volume MG_0003, version 1 The F-MIDR products, F50S345, F55N337, F60N334, F65N330 and F75N332, on CD-ROM MG_0003 are the standard product replacements for five of the engineering test product F-MIDRD's on MG_0001. 5. Comments on GEO.LBL for Volumes MG_0001 to MG_0022 The PDS label file GEO.LBL on Magellan CD's volumes 1 to 22 contain incorrect DESCRIPTION keyword entries for the objects MINIMUM_LONGITUDE and MAXIMUM_LONGITUDE. The correct entries for these objects are: OBJECT = COLUMN NAME = MINIMUM_LONGITUDE DATA_TYPE = REAL UNIT = DEGREE START_BYTE = 19 BYTES = 8 DESCRIPTION = "The minimum_longitude element specifies the westernmost (left_most) longitude of the feature." END_OBJECT = COLUMN OBJECT = COLUMN NAME = MAXIMUM_LONGITUDE DATA_TYPE = REAL UNIT = DEGREE START_BYTE = 28 BYTES = 8 DESCRIPTION = "The maximum_longitude element specifies the easternmost (right_most) longitude of the feature." END_OBJECT = COLUMN Previously, the DESCRIPTION keyword for MINIMUM_LONGITUDE referred to "easternmost" and the DESCRIPTION keyword for MAXIMUM_LONGITUDE referred to "westernmost". 6. Comments on Volume MG_0012 Framelet 56 for C1-MIDR 60N014 has zeros in approximately 6.5 records starting at line 605 sample 513 and continuing to line 611 sample 1024. This will result in a horizontal black band across the framelet and may cause problems with some automated processing algorithms. 7. Comments on Volume MG_0014 Framelet 36 for C1-MIDR 00N009 has zeros in approximately 7 records starting at line 316 sample 513 and continuing to line 323 sample 512. This will result in a horizontal black band across the framelet and may cause problems with some automated processing algorithms. 8. Comments on Volume MG_0015 Framelet 22 for F-MIDR 20N097 has zeros in approximately 6 records starting at line 360 sample 513 and continuing to line 366 sample 512. This will result in a horizontal black band across the framelet and may cause problems with some automated processing algorithms. 9. Comments on Volumes MG_0023 to MG_0026 The PUBLICATION_DATE keyword in MCUMCOMM.TXT shows an incorrect date. The date is supposed to be 1991-10-03 not 1991-09-03. 10. Comments on Volume MG_0030 The file CONTENTS.TAB, in directory INDEX, shows 141 as the maximum longitude for product C1_75N119. The maximum longitude entry for this product should be 186. 11. Comments on Volume MG_0038 The VICAR labels for all image files (*.IMG) in the directory F45N241 incorrectly list this product as being 'F-MIDR.45N241;1'. This product is actually 'F-MIDR.45N241;2', i.e. version 2. The detached PDS labels in this directory are correct. 12. Comments on Volume MG_0041 12.1 Comments on FRAME.TAB The file FRAME.TAB in directory C175N209 incorrectly reports the maximum longitude of framelet C1F02 to be 175.9575. This should be 183.4368. Also, FRAME.TAB reports the minimum longitude of framelet C1F03 to be 183.4495. The minimum longitude for framelet C1F03 is 175.9738. (Although locations are reported to four significant figures, spatial accuracy is actually much lower.) 12.2 Comments on [C175N209]C1F02.LBL The MAXIMUM_LONGITUDE keyword in this file has a value of 175.9575. The value should be 183.4368. 12.3 Comments on [C175N209]C1F03.LBL The MINIMUM_LONGITUDE keyword in this file has a value of 183.4495. The value should be 175.9738. 12.4 Comments on CONTENTS.TAB The file CONTENTS.TAB, in directory INDEX, reports 186 as the minimum longitude for product C1_75N209. The minimum longitude entry for this product should be 142. 13. Comments on Volume MG_0043 The file CONTENTS.TAB, in subdirectory INDEX, reports the maximum latitude (northernmost), the minimum latitude (southernmost), the maximum longitude (easternmost) and the minimum longitude (westernmost). Since the product C2-MIDR 60N033 on this CD lies in the far northern hemisphere, the image wraps around itself. Consequently, the maximum longitude and minimum longitude entries in CONTENTS.TAB are not appropriate indications of the longitude limits for this image. These entries in CONTENTS.TAB have therefore been set to 0. This approach adheres to the file structure given in the MIDRCD SIS. Note that the top edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. 14. Comments on GEO.TAB on all volumes GEO.TAB contains names and locations of specific features on Venus. The file is dynamic and contains a number of spelling and location errors. The file is periodically updated, and the user should be careful in using this data. Contact Raymond Batson if you have comments on GEO.TAB. Raymond Batson Branch of Astrogeology U.S. Geological Survey 2255 North Gemini Drive Flagstaff, Arizona 86001 (602) 556-7260 NASAmail: RAY.BATSON 15. Comments on PDS Data Set Map Project Keyword Descriptions on all volumes The following information, concerning the definitions of some PDS keywords, should be added to the DATA_SET_MAP_PROJECT_CATALOG descriptions contained in [LABEL]DSMAP*.LBL files. NOTE: The PDS keywords whose names begin 'X_' and 'Y_', e.g. X_AXIS_PROJECTION_OFFSET, Y_AXIS_PROJECTION_OFFSET, etc., use 'X' to denote LINE and 'Y' to denote SAMPLE. This is reversed relative to the definitions in Snyder (1987), i.e. x(Snyder) = y(PDS), and y(Snyder) = -x(PDS). Snyder, John P., (1987) "Map projections -- a working manual", U. S. Geol. Surv. Prof. Paper 1395, 383p., 1987. 16. Comments on Volume MG_0051 The C2 MIDR's C260N333, C260N153 and C260N093 on this CD lie far enough north so that the top boundaries of these products actually wrap around themselves. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), for these products are not an appropriate indication of the limits of these products. These entries have therefore been set to 0. Latitude and longitude limits for these products can be obtained from the VICAR label or from the file FRAME.TAB. C260N333 the top edge of this product extends for 401 degrees, from 132.1 degrees, through 360 degrees and continuing to 173.2 degrees. C260N153 the top edge of this product extends for 401 degrees, from 312.1 degrees, through 360 degrees and continuing to 353.2 degrees. C260N093 the top edge of this product extends for 401 degrees, from 252.1 degrees, through 360 degrees and continuing to 293.2 degrees. 17. Comments on "PRODUCT_ID" for Volumes MG_0053 and Above With the advent of cycle 2 data on volume MG_0053, it was decided to alter the format and meaning of PRODUCT_ID version numbers (note that the version number follows the ";" in the PRODUCT_ID). If the PRODUCT_ID has a single digit version number (e.g. F-MIDR.25N333;1), the product is a cycle 1 product. In this case, a higher version number means an improved version of the same product. If the PRODUCT_ID has a three digit version number (e.g. F-MIDR.15S049;201), the version number format is : product_name;cvv where c is the cycle number vv is a "version" number. However, in this case the version number does NOT necessarily refer to an improved version of the same product. It may mean that this is a completely different type of MIDR product at this latitude and longitude. For example, F-MIDR.nnzmmm;202 may be a right looking image while F-MIDR.nnzmmm;201 is a left looking one. The file [INDEX]CONTENTS.TAB will provide this information. 18. Comments on GEOM.TAB for MG_0001 to MG_0052 The file GEOM.TAB in each product sub-directory contains geometry information such as orbit number, boresight longitude and latitude, etc. The orbit numbers referenced in these files on CD's 1 to 52 are incorrect. The table entry for orbit number was 3 bytes long when it should have been 4 bytes. Cycle 1 and cycle 2 orbit numbers were also intermixed. These files should not be used. The problem has been fixed for MG_0053 and future CD's. Corrected versions of past GEOM.TAB files will be available on a future CD. 19. Comments on GEO.TAB for MG_0001 to MG_0052 The file GEO.TAB, contained in the top level directory, reports the positions and types of Venus features. Up to and including CD 52 this file has included the names of provisional features. Starting with CD 53, GEO.TAB includes only the names of IAU (International Astronomical Union) approved features. 20. Comments on Volume MG_0054 20.1 [INDEX]CONTENTS.TAB Values The C2 MIDR's C260N213, C260S213, C260S153, C260S093, C260S033 and C260S273 on this CD lie far enough north (or south) so that the top (or bottom) boundaries of these products wrap around themselves. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), for these products are not an appropriate indication of the limits of these products. These entries have therefore been set to 0. Latitude and longitude limits for these products can be obtained from the VICAR label or from the file FRAME.TAB. C260N213 the top edge of this product extends for 401 degrees, from 12.1 degrees, through 360 degrees and continuing to 53.2 degrees. C260S213 the bottom edge of this product extends for 401 degrees, from 12.1 degrees, through 360 degrees and continuing to 53.2 degrees. C260S153 the bottom edge of this product extends for 401 degrees, from 312.1 degrees, through 360 degrees and continuing to 353.2 degrees. C260S093 the bottom edge of this product extends for 401 degrees, from 252.1 degrees, through 360 degrees and continuing to 293.2 degrees. C260S033 the bottom edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. C260S273 the bottom edge of this product extends for 401 degrees, from 72.1 degrees, through 360 degrees and continuing to 113.2 degrees. 20.2 VICAR Label Keywords for Product C160N347 VICAR labels in Magellan image files contain a keyword "IMAGE". This keyword is supposed to have the value "NORMALIZED RADAR CROSS SECTION". The VICAR keyword "IMAGE" in all image files (*.IMG) for the product C160N347 on volume MG_0054, contains the incorrect value "RADAR CROSS SECTION POWER". 21. Comments on Volume MG_0060 21.1 [INDEX]MCUMDIR.LBL The PDS label file [INDEX]MCUMDIR.LBL is missing a line (the fifth record) containing the ^TABLE value. The fifth record of this file should be: ^TABLE = "MCUMDIR.TAB" 21.2 Version number for [C100N060] The keyword "PRODUCT", in the VICAR labels for the files BROWSE.IMG and C1F*.IMG, incorrectly list this product as being 'C1-MIDR.00N060;201'. The product in this directory is 'C1-MIDR.00N060;202'. This is a cycle 2 product with a "right" look direction. The product in directory C100N060 of volume MG_0057 is the 201 ("left" look direction) version of C100N060. Since the VICAR labels were incorrect, the "IMAGE_ID" keyword in the following files also incorrectly refer to this product as 'C1-MIDR.00N060;201': [INDEX]CONTENTS.TAB [C100N060]BROWSE.LBL [C100N060]C1F*.LBL [C100N060]FRAME.LBL [C100N060]HIST.LBL This product, 'C1-MIDR.00N060;202', is correctly referred to by the file [INDEX]MCUMDIR.TAB and by the product listing associated with MCUMCOMM.TXT. 22. Comments on Volume MG_0061 22.1 [INDEX]CONTENTS.TAB Values The C2 MIDR's C260N033, C260N153 and C260N273 on this CD lie far enough north so that the top boundaries of these products wrap around themselves. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), for these products are not an appropriate indication of the limits of these products. These entries have therefore been set to 0. The actual limits of these products are: C260N033 the top edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. C260N153 the top edge of this product extends for 401 degrees, from 312.1 degrees, through 360 degrees and continuing to 353.2 degrees. C260N273 the top edge of this product extends for 401 degrees, from 72.1 degrees, through 360 degrees and continuing to 113.2 degrees. 22.2 [INDEX]MCUMDIR.LBL This file has the wrong record format. It is a variable length (max 255 byte) file. The file should be: fixed length, 80 byte. 23. Comments on Volume MG_0063 23.1 [INDEX]MCUMDIR.LBL The fifth record, which contains the entry for ^TABLE, is missing the carriage return character (ASCII 13) in the 79th byte and the line feed character (ASCII 10) in the 80th byte. This may cause a problem for automated procedures which use this file. 23.2 [INDEX]MCUMDIR.TAB The last seven records of this file are a repeat of the previous seven records. 24. Comments on [INDEX]MCUMDIR.TAB for MG_0064 to MG_0066 The file [INDEX]MCUMDIR.TAB on these CD's is an exact duplicate of the MCUMDIR.TAB file on CD 63. The file was not updated for new entries and contains the repeated entries reported in section 22.2. 25. Comments Concerning VMS Record Attributes of IMAGE Files on All Volumes Image files (*.IMG) and HIST.TAB files for all products on MIDR CD's use a "print file carriage control" record attribute instead of a null "carriage control" record attribute. This will cause a problem when using the COPY command in VMS. In general there is no reason to COPY these files, as applications such as TAE or the standard FORTRAN library can access the files without any difficulty. The files can be copied, if necessary, using the VMS utility "CONVERT". Use any editor to produce a file called MIDR.FDL, which should contain the following lines: RECORD CARRIAGE_CONTROL none FORMAT fixed SIZE 1024 The file can be "converted" to the hard disk using the command: CONVERT/FDL=MIDR.FDL cddev:[directory1]file.IMG disk:[directory2]file.IMG where: cddev is the VMS device name for the CD reader, directory1 is the directory name containing the image file to be converted, directory2 is the name of the directory where the converted file is to be placed, disk is the VMS device name for your hard disk, and file is the name of of the file to be converted. For example, to convert a BROWSE.IMG file in the directory C260N273 on MG_0061, where the CD reader is the device DUB0: and the converted file is to be put onto the hard disk DUA0:, the command would be: CONVERT/FDL=MIDR.FDL DUB0:[C260N273]BROWSE.IMG DUA0:[MINE]BROWSE.IMG 26. Comments on [LABEL]C3MIDRDS.LBL on Volume MG_0068 and Above Starting with MG_0068 the description of C3-MIDRD's in [LABEL]C3MIDRDS.LBL has been changed to more accurately read: "One C3-MIDR frame covers 137.5 degrees in latitude and 157 degrees in longitude, at the equator." instead of: "One C3-MIDR frame covers 80 degrees in latitude and 120 degrees in longitude. No C3-MIDRs were generated during the first mapping cycle." 27. Comments on Volume MG_0069 27.1 [INDEX]CONTENTS.TAB Values The C2 MIDR C260S333 lies far enough south so that the bottom boundary of this product wraps around itself. The C3 MIDR C314N180 also wraps around itself due to the extreme scale of C3 MIDR's. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), for these products are not an appropriate indication of the limits of these products. The entries for maximum longitude and minimum longitude in the file [INDEX]CONTENTS.TAB have therefore been set to 0. In some cases, for C3 MIDR's, an individual framelet has a longitude extent of more than 360 degrees. The maximum and minimum longitude entries in FRAME.TAB have also been set to 0 when this occurs. The latitude and longitude extents of these frames can be found from the VICAR label for each framelet. C260S333 the bottom edge of this product extends for 401 degrees, from 132.1 degrees, through 360 degrees and continuing to 173.2 degrees. C314N180 the top edge of this product extends for 1203.3 degrees, from 298.4 degrees, through 1080 degrees and continuing to 61.7 degrees. 27.2 [C314N180]FRAME.TAB Values Note that individual framelets for the product C314N180, also wrap around themselves. Thus maximum and minimum longitude entries for some framelets in the file [C314N180]FRAME.TAB have been set to 0. Latitude and longitude limits for these products can be obtained from the VICAR label. 27.3 [C314N180] PDS Label Files The detached PDS label files for framelets C3F01, C3F02, C3F07 and C1F08 should have had the values of keywords MAXIMUM_LONGITUDE and MINIMUM_LONGITUDE set to 0. Latitude and longitude product limits in the detached PDS label files should conform to those in the file FRAME.TAB. This was not done for this product. 28. Comments on Volumes MG_0070, MG_0071, MG_0072 and MG_0073 The file [INDEX]MCUMDIR.TAB is a cumulative listing of all CD-ROM products to date. This file contains a field (start_byte 44) for the CD-ROM publication date. The publication dates listed for the MG_0070 and MG_0071 products show a 1991 date. This date should be 1992. The [INDEX]MCUMDIR.TAB files on MG_0070, MG_0071, MG_0072 and MG_0073 contain this error. 29. Comments on GEO.TAB on all volumes GEO.TAB contains the names, locations and geologic type of specific features on Venus. The file is dynamic and is periodically updated. GEO.TAB on volumes MG_0001 to MG_0052 contains provisional names as well as IAU (International Astronomical Union) approved names. Volumes MG_0053 to MG_0073 have GEO.TAB files which contain only IAU approved names. GEO.TAB on volume MG_0074 and subsequent volumes is an updated list of features. It contains IAU approved and provisional names as of June 1992. 30. Comments on Volume MG_0078 30.1 [INDEX]CONTENTS.TAB Values Due to the extreme scale of C3 MIDR's the top edge (in the case of northern products) or the bottom edge (in the case of southern products) wraps around itself. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), are not an appropriate indication of the limits of these products. The entries for maximum longitude and minimum longitude in [INDEX]CONTENTS.TAB have therefore been set to 0. In some cases, an individual framelet has a longitude extent of more than 360 degrees. The maximum and minimum longitude entries in FRAME.TAB have also been set to 0 when this occurs. The latitude and longitude extents for these frames can be found from the VICAR label for each framelet. C314N060 the top edge of this product extends for 1203.3 degrees, from 178.4 degrees, through 1080 degrees and continuing to 301.6 degrees. C314N300 the top edge of this product extends for 1203.3 degrees, from 58.4 degrees, through 1080 degrees and continuing to 181.6 degrees. C314S060 the bottom edge of this product extends for 1203.3 degrees, from 178.4 degrees, through 1080 degrees and continuing to 301.6 degrees. C314S180 the bottom edge of this product extends for 1203.3 degrees, from 298.4 degrees, through 1080 degrees and continuing to 61.6 degrees. C314S300 the bottom edge of this product extends for 1203.3 degrees, from 58.4 degrees, through 1080 degrees and continuing to 181.6 degrees. 30.2 FRAME.TAB Values for C3 MIDRD's Note that individual framelets for the products C314N060, C314N300, C314S060, C314S18 and C314S300 also wrap around themselves. Thus maximum and minimum longitude entries for framelets C3F01, C3F02, C3F07 and C3F08, in the case of north C3 MIDRD's, or framelets C3F49, C3F50, C3F55 and C3F56, in the case of south C3 MIDRD's, in the file FRAME.TAB have been set to 0. Latitude and longitude limits for these products can be obtained from the VICAR label. 30.3 PDS Label Files for C3 MIDRD's The detached PDS label files for framelets C3F01, C3F02, C3F07 and C3F08 in directories [C314N060] and [C314N300], and framelets C3F49, C3F50, C3F55 and C3F56 in [C314S060], [C314S180] and [C314S300] should have had the values of keywords MAXIMUM_LONGITUDE and MINIMUM_LONGITUDE set to 0. Latitude and longitude product limits in the detached PDS label files should conform to those in the FRAME.TAB files. This was not done for these products. 31. Comments on MCUMCOMM.TXT product lists for MG_0027 to MG_0080 Starting with MG_0027, a list of MIDR products sorted by longitude and latitude is appended to the MCUMCOMM.TXT file. This list includes all products from MG_0001 up to and including the CD the list appears on. A number of mistakes have been found in this list. CD NUMBER LIST (incorrect) SHOULD BE 5 F65S005;1 F65S005;2 38 F45N241;1 F45N241;2 51 C175S066;1 C175S068;1 51 C200N337;1 C200N337;2 51 C250N333;1 C260N333;2 51 C250N153;1 C260N153;2 51 C230N335;1 C230N335;2 66 F45S188;1 F45N188;1 These errors have been corrected for the lists on MG_0081 and above. 32. Comments on Volume MG_0081 The C2 MIDR C260N333 on this CD lies far enough north so that the top boundary of this product wraps around itself. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost) are not an appropriate indication of the limits of this product. These entries have therefore been set to 0. Latitude and longitude limits can be obtained from the VICAR label or from the file FRAME.TAB. The actual limits are: C260N333 the top edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. 33. Comments on Volume MG_0082 Seven C2 MIDR's on this CD lie far enough north (or south) so that the top (or bottom) boundaries of these products wrap around themselves. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost) are not appropriate indications of the limits of these products. These entries have therefore been set to 0. Latitude and longitude limits can be obtained from the VICAR label or from the file FRAME.TAB. The actual limits are: C260N153 the top edge of this product extends for 401 degrees, from 312.1 degrees, through 360 degrees and continuing to 353.2 degrees. C260S033 the bottom edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. C260S093 the bottom edge of this product extends for 401 degrees, from 252.1 degrees, through 360 degrees and continuing to 293.2 degrees. C260S273 the bottom edge of this product extends for 401 degrees, from 72.1 degrees, through 360 degrees and continuing to 113.2 degrees. C260S153 the bottom edge of this product extends for 401 degrees, from 312.1 degrees, through 360 degrees and continuing to 353.2 degrees. C260S213 the bottom edge of this product extends for 401 degrees, from 12.1 degrees, through 360 degrees and continuing to 53.2 degrees. C260S333 the bottom edge of this product extends for 401 degrees, from 132.1 degrees, through 360 degrees and continuing to 173.2 degrees. 34. Comments on Volume MG_0083 Five C2 MIDR's on this CD lie far enough north (or south) so that the top (or bottom) boundaries of these products wrap around themselves. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost) are not appropriate indications of the limits of these products. These entries have therefore been set to 0. Latitude and longitude limits can be obtained from the VICAR label or from the file FRAME.TAB. The actual limits are: C260S033 the bottom edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. C260S273 the bottom edge of this product extends for 401 degrees, from 72.1 degrees, through 360 degrees and continuing to 113.2 degrees. C260S333 the bottom edge of this product extends for 401 degrees, from 132.1 degrees, through 360 degrees and continuing to 173.2 degrees. C260N093 the top edge of this product extends for 401 degrees, from 252.1 degrees, through 360 degrees and continuing to 293.2 degrees. C260N033 the top edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. 35. Comments on Volume MG_0084 35.1 [INDEX]CONTENTS.TAB Values The C2 MIDR C260N033 lies far enough north so that the top boundary of this product wraps around itself. The C3 MIDR's C314S060 and C314N300 also wrap around themselves, due to the extreme scale of C3 MIDR's. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), for these products are not an appropriate indication of the limits of these products. The entries for maximum longitude and minimum longitude in the file [INDEX]CONTENTS.TAB have therefore been set to 0. In the case of C3 MIDR's, an individual framelet may have a longitude extent of more than 360 degrees. C260N033 the top edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. C314S060 the bottom edge of this product extends for 1203.3 degrees, from 178.4 degrees, through 1080 degrees and continuing to 301.6 degrees. C314N300 the top edge of this product extends for 1203.3 degrees, from 58.4 degrees, through 1080 degrees and continuing to 181.6 degrees. 35.2 FRAME.TAB Values for C3 MIDRD's Note that individual framelets for the products C314S060 and C314N300 also wrap around themselves. Thus maximum and minimum longitude entries for framelets C3F01, C3F02, C3F07 and C3F08, in the case of the north C3 MIDRD, or framelets C3F49, C3F50, C3F55 and C3F56, in the case of the south C3 MIDRD, in the file FRAME.TAB have been set to 0. Latitude and longitude limits for these products can be obtained from the VICAR label. 35.3 Look Angle for [C230N026] The C1 MIDRD's used to create the product C2-MIDR.30N026;301 were created using a combination of orbits designated as STEREO orbits and MAXWELL orbits. 36. Comments on Volume MG_0085 36.1 [INDEX]CONTENTS.TAB Values The C3 MIDR C314N180 wraps around itself due to the extreme scale of C3 MIDR's. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), for this product are not an appropriate indication of the limits of this MIDR. The entries for maximum longitude and minimum longitude in the file [INDEX]CONTENTS.TAB have therefore been set to 0. C314N060 the top edge of this product extends for 1203.3 degrees, from 178.4 degrees, through 1080 degrees and continuing to 301.6 degrees. 36.2 [C314N060]FRAME.TAB Values Note that individual framelets for the product C314N060, also wrap around themselves. Thus maximum and minimum longitude entries for framelets C3F01, C3F02, C3F07 and C3F08 in the file [C314N060]FRAME.TAB have been set to 0. Latitude and longitude limits for these products can be obtained from the VICAR label. 37. Comments on Volume MG_0118 Four C2 MIDR's on this CD lie far enough north so that the top boundaries of these products wrap around themselves. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost) are not appropriate indications of the limits of these products. These entries have therefore been set to 0. Latitude and longitude limits can be obtained from the VICAR label or from the file FRAME.TAB. The actual limits are: C260S333 the bottom edge of this product extends for 401 degrees, from 132.1 degrees, through 360 degrees and continuing to 173.2 degrees. C260N093 the top edge of this product extends for 401 degrees, from 252.1 degrees, through 360 degrees and continuing to 293.2 degrees. C260N033 the top edge of this product extends for 401 degrees, from 192.1 degrees, through 360 degrees and continuing to 233.2 degrees. C260N153 the top edge of this product extends for 401 degrees, from 312.1 degrees, through 360 degrees and continuing to 353.2 degrees. 38. Comments on Volume MG_0119 38.1 Products Included on MG_0119 Compressed Mosaic Image Data Records (C-MIDRD's) and Full-resolution Mosaic Image Data Records (F-MIDR's) have been placed on separate CD's up to MG_0118. MG_0119 contains F-MIDRD's as well as C2-MIDRD's and C3-MIDRD's since there are not enough C-MIDRD's planned for distribution to comprise a full CD. 38.2 [INDEX]CONTENTS.TAB Values Due to the extreme scale of C3 MIDR's the top edge (in the case of northern products) or the bottom edge (in the case of southern products) wraps around itself. Consequently, the entries in [INDEX]CONTENTS.TAB, maximum longitude (easternmost) and minimum longitude (westernmost), are not an appropriate indication of the limits of these products. The entries for maximum longitude and minimum longitude in [INDEX]CONTENTS.TAB have therefore been set to 0. In some cases, an individual framelet has a longitude extent of more than 360 degrees. The maximum and minimum longitude entries in FRAME.TAB have also been set to 0 when this occurs. The latitude and longitude extents for these frames can be found from the VICAR label for each framelet. C314N060 the top edge of this product extends for 1203.3 degrees, from 178.4 degrees, through 1080 degrees and continuing to 301.6 degrees. C314N300 the top edge of this product extends for 1203.3 degrees, from 58.4 degrees, through 1080 degrees and continuing to 181.6 degrees. C314N180 the top edge of this product extends for 1203.3 degrees, from 298.4 degrees, through 1080 degrees and continuing to 61.6 degrees. 39. Product Lists for Volumes MG_0001 to MG_0122 The following is a list of MIDR products, sorted by longitude then by latitude (from north pole to south pole). PRODUCT TYPE: FMIDRS PRODUCT CD CYCLE PRODUCT CD CYCLE PRODUCT CD CYCLE F_25N003;1 7 1 F_40S131;1 18 1 F_00N217;1 27 1 F_25N003;301 87 3 F_60N132;1 18 1 F_05S217;1 28 1 F_20N003;1 7 1 F_10N132;1 17 1 F_30S218;201 74 2 F_20N003;301 87 3 F_10N132;301 108 3 F_30S218;1 71 1 F_20S003;1 6 1 F_05N132;1 17 1 F_45S218;201 68 2 F_25S003;1 6 1 F_05N132;301 108 3 F_45S218;1 29 1 F_30S003;1 6 1 F_00N132;1 17 1 F_15N220;1 66 1 F_35S003;1 6 1 F_00N132;301 108 3 F_15S220;1 67 1 F_45N004;1 7 1 F_05S132;301 110 3 F_20S221;201 73 2 F_40S004;1 6 1 F_05S132;1 15 1 F_20S221;1 29 1 F_60N005;1 8 1 F_10S132;1 15 1 F_05S222;1 32 1 F_60N005;301 122 3 F_10S132;301 104 3 F_40S222;1 29 1 F_60S005;1 5 1 F_15S134;1 94 1 F_25N223;1 32 1 F_65S005;2 5 1 F_15S134;301 108 3 F_15S226;1 67 1 F_65N006;1 8 1 F_30S136;1 15 1 F_45S226;201 98 2 F_65S006;201 111 2 F_30S136;301 110 3 F_45S226;1 76 1 F_70N007;1 7 1 F_25S137;301 110 3 F_20N227;1 32 1 F_25S009;1 7 1 F_25S137;1 94 1 F_20S227;201 73 2 F_30S009;1 7 1 F_35S137;201 63 2 F_20S227;1 67 1 F_40S011;1 80 1 F_35S137;301 104 3 F_10N228;1 38 1 F_45S012;1 80 1 F_35S137;1 77 1 F_05N228;1 32 1 F_50S013;201 80 2 F_40N138;301 93 3 F_25N229;1 32 1 F_50S013;1 18 1 F_40S138;1 13 1 F_40N230;1 35 1 F_15N014;1 11 1 F_40S138;201 63 2 F_35N230;1 35 1 F_15N014;301 87 3 F_40S138;301 108 3 F_40S230;1 32 1 F_10N014;301 98 3 F_20S139;301 110 3 F_50S230;201 75 2 F_10N014;1 10 1 F_20S139;1 94 1 F_50S230;1 71 1 F_55S014;201 75 2 F_15S140;301 109 3 F_20N233;1 36 1 F_55S014;1 18 1 F_15S140;1 93 1 F_20S233;1 35 1 F_60N016;1 7 1 F_30S142;202 68 2 F_10N234;1 32 1 F_60S016;201 77 2 F_30S142;201 63 2 F_45S234;201 74 2 F_60S016;1 8 1 F_30S142;1 53 1 F_45S234;1 67 1 F_65N018;1 7 1 F_30S142;301 111 3 F_45S234;301 108 3 F_40N018;1 7 1 F_45S142;1 38 1 F_45S234;202 121 2 F_45N019;1 11 1 F_25N143;301 109 3 F_55N236;1 36 1 F_45S019;201 75 2 F_25N143;1 93 1 F_75N237;1 36 1 F_45S019;1 18 1 F_35S143;301 109 3 F_30N237;1 38 1 F_15N020;1 11 1 F_35S143;202 68 2 F_15N237;1 35 1 F_15N020;301 86 3 F_35S143;201 63 2 F_15S237;1 35 1 F_10N020;1 8 1 F_35S143;1 53 1 F_20N239;1 35 1 F_10N020;301 86 3 F_10S144;1 120 1 F_05N239;1 36 1 F_05N020;1 110 1 F_20N145;1 17 1 F_05S239;1 35 1 F_05N020;301 121 3 F_20N145;301 109 3 F_45N241;2 38 1 F_15S020;1 105 1 F_20S145;301 109 3 F_15S243;1 38 1 F_50N021;1 8 1 F_20S145;1 18 1 F_35S243;1 35 1 F_50S021;1 39 1 F_40S145;201 68 2 F_40N244;1 42 1 F_50S021;201 75 2 F_40S145;1 18 1 F_40S244;1 35 1 F_30S022;1 10 1 F_40S145;301 109 3 F_10S245;1 39 1 F_55N023;1 8 1 F_15S146;1 122 1 F_20S245;1 39 1 F_40N025;1 8 1 F_50N147;1 26 1 F_50N247;1 39 1 F_60N026;1 8 1 F_50S147;1 76 1 F_25S247;1 39 1 F_60N026;301 87 3 F_00N149;1 111 1 F_45N249;1 39 1 F_25N028;1 105 1 F_00N149;201 110 2 F_15N249;1 36 1 F_10N031;201 58 2 F_00N149;301 106 3 F_15S249;1 38 1 F_05S031;201 59 2 F_05S149;301 119 3 F_05S250;1 36 1 F_10S031;1 106 1 F_05S149;1 111 1 F_10S250;1 39 1 F_20S033;1 105 1 F_05S149;201 105 2 F_35S250;1 94 1 F_25S034;1 105 1 F_35N150;301 120 3 F_40N251;1 44 1 F_30N035;201 56 2 F_35N150;1 106 1 F_20S251;1 39 1 F_15N037;301 107 3 F_55N152;1 23 1 F_25S253;1 42 1 F_15N037;201 56 2 F_00N155;201 119 2 F_15S254;1 38 1 F_00N037;201 55 2 F_00N155;1 111 1 F_30N256;1 38 1 F_05S037;201 55 2 F_00N155;301 104 3 F_20S257;1 38 1 F_20N038;301 122 3 F_05S155;301 111 3 F_25N259;1 70 1 F_20N038;201 56 2 F_05S155;201 108 2 F_25S259;1 42 1 F_30N041;201 56 2 F_05S155;2 107 1 F_15N260;1 36 1 F_30S041;201 58 2 F_05S155;1 93 1 F_15S260;1 38 1 F_10N042;201 58 2 F_10S155;301 109 3 F_30N262;1 36 1 F_00N042;201 55 2 F_10S155;1 23 1 F_30S262;1 42 1 F_05S042;201 55 2 F_30S155;1 107 1 F_55N263;1 42 1 F_15N043;201 55 2 F_20S156;301 107 3 F_50N264;1 42 1 F_15N043;301 86 3 F_20S156;1 23 1 F_15N266;1 45 1 F_35S043;201 74 2 F_25S156;301 105 3 F_10N267;1 45 1 F_20N044;201 58 2 F_25S156;1 23 1 F_10S267;1 36 1 F_20N044;301 86 3 F_45N157;1 66 1 F_30N269;1 44 1 F_40N046;201 56 2 F_35N157;301 109 3 F_20N269;1 44 1 F_25N046;201 55 2 F_35N157;1 80 1 F_30S269;1 42 1 F_30N047;201 55 2 F_15S157;201 73 2 F_60N270;1 42 1 F_10N048;201 55 2 F_15S157;301 102 3 F_35N270;1 44 1 F_05N048;201 55 2 F_15S157;1 23 1 F_35S270;1 67 1 F_00N048;201 58 2 F_35S157;301 105 3 F_40N272;1 44 1 F_15N049;201 55 2 F_35S157;1 76 1 F_25N272;1 87 1 F_15N049;301 86 3 F_40N159;1 66 1 F_40S272;1 67 1 F_15S049;201 53 2 F_40N159;301 109 3 F_50S272;1 39 1 F_35N050;201 62 2 F_30N161;301 106 3 F_10N273;1 45 1 F_20N050;201 56 2 F_30N161;1 65 1 F_05N273;1 45 1 F_25N052;201 62 2 F_30S161;301 109 3 F_10S273;1 45 1 F_40N053;201 62 2 F_30S161;1 23 1 F_30N275;1 44 1 F_50N054;1 13 1 F_65N162;1 26 1 F_20N275;1 93 1 F_30N054;201 63 2 F_20S162;201 64 2 F_30S275;1 45 1 F_30N054;301 121 3 F_20S162;301 106 3 F_35N277;1 44 1 F_15N054;301 122 3 F_20S162;1 24 1 F_15S277;1 70 1 F_15N054;201 62 2 F_25S162;1 23 1 F_35S277;1 71 1 F_10N054;201 62 2 F_25S162;301 102 3 F_25N278;1 50 1 F_05N054;201 62 2 F_50N163;1 66 1 F_40N279;1 45 1 F_00N054;201 62 2 F_35N163;1 65 1 F_10N279;1 49 1 F_05S054;201 62 2 F_35N163;301 102 3 F_00N279;1 46 1 F_10S054;201 56 2 F_15S163;201 64 2 F_05S279;1 46 1 F_15S054;201 58 2 F_15S163;301 102 3 F_10S279;1 70 1 F_00N059;301 122 3 F_15S163;1 23 1 F_40S279;1 49 1 F_00N059;1 59 1 F_35S163;1 23 1 F_20N280;1 46 1 F_05S059;301 122 3 F_35S163;301 102 3 F_20S280;1 70 1 F_05S059;1 59 1 F_60N164;1 26 1 F_45S280;1 49 1 F_10S059;1 59 1 F_60S164;1 63 1 F_60N281;1 45 1 F_10S059;301 122 3 F_40N166;301 119 3 F_30N281;1 42 1 F_55N060;1 11 1 F_40N166;1 103 1 F_35N283;1 44 1 F_15S060;201 73 2 F_10N166;1 65 1 F_15N283;1 93 1 F_10N065;301 86 3 F_10N166;301 102 3 F_15S283;1 46 1 F_10N065;201 59 2 F_40S166;1 121 1 F_35S283;1 71 1 F_10N065;1 13 1 F_30N167;1 65 1 F_25N284;1 42 1 F_05N065;1 9 1 F_30N167;301 101 3 F_10N284;1 45 1 F_05N065;301 86 3 F_20S168;201 74 2 F_05N284;1 45 1 F_00N065;301 87 3 F_20S168;1 70 1 F_00N284;1 49 1 F_00N065;1 9 1 F_20S168;301 107 3 F_05S284;1 70 1 F_05S065;1 10 1 F_25S168;201 74 2 F_10S284;1 46 1 F_10S065;1 10 1 F_25S168;1 71 1 F_40N286;1 46 1 F_30N066;1 80 1 F_25S168;202 107 2 F_20N286;1 46 1 F_05N070;1 9 1 F_25S168;301 101 3 F_20S286;1 39 1 F_00N070;1 9 1 F_15N169;1 65 1 F_40S286;1 49 1 F_00N070;201 72 2 F_15N169;301 102 3 F_30N287;1 44 1 F_05S070;301 106 3 F_15S169;201 73 2 F_30S287;1 94 1 F_05S070;1 9 1 F_15S169;1 65 1 F_15S289;1 46 1 F_10S070;1 9 1 F_15S169;301 102 3 F_35N290;1 36 1 F_10S070;301 106 3 F_35N170;301 111 3 F_10N290;1 59 1 F_40S074;1 18 1 F_35N170;1 103 1 F_05N290;1 46 1 F_10N076;201 80 2 F_35S170;301 102 3 F_00N290;1 93 1 F_10N076;1 66 1 F_35S170;1 76 1 F_05S290;1 70 1 F_10N076;301 107 3 F_55N171;1 66 1 F_10S290;1 46 1 F_05N076;1 8 1 F_55S171;1 77 1 F_35S290;1 49 1 F_00N076;1 9 1 F_50N172;1 27 1 F_55N291;1 49 1 F_05S076;1 9 1 F_10N172;1 65 1 F_20N292;1 44 1 F_10S076;1 9 1 F_10N172;301 101 3 F_40S293;1 71 1 F_35N077;1 11 1 F_30N174;1 65 1 F_65N294;1 58 1 F_35N077;201 80 2 F_25N174;1 64 1 F_30N294;1 50 1 F_15S077;202 103 2 F_20N174;1 62 1 F_45N295;1 49 1 F_15S077;1 66 1 F_15N174;1 65 1 F_05S295;1 50 1 F_45N080;1 11 1 F_15N174;301 101 3 F_70N296;1 49 1 F_20N080;1 15 1 F_15S174;201 73 2 F_25N296;1 50 1 F_20N080;201 87 2 F_15S174;1 68 1 F_25S296;1 50 1 F_20N080;202 98 2 F_15S174;301 101 3 F_50N297;1 49 1 F_45N081;201 71 2 F_20S174;201 73 2 F_35N297;1 50 1 F_40N081;1 103 1 F_20S174;1 65 1 F_30N300;1 52 1 F_25N082;1 120 1 F_20S174;301 101 3 F_40S300;1 50 1 F_10N082;1 120 1 F_25S174;201 74 2 F_10N301;1 93 1 F_05N082;1 10 1 F_25S174;1 71 1 F_05N301;1 52 1 F_05N082;301 86 3 F_25S174;301 101 3 F_10S301;1 50 1 F_00N082;1 10 1 F_60S175;201 94 2 F_60N302;1 59 1 F_00N082;301 86 3 F_60S175;1 77 1 F_25S302;1 52 1 F_05S082;301 87 3 F_10N177;1 24 1 F_35N303;1 63 1 F_05S082;1 8 1 F_05N177;1 23 1 F_65N306;1 56 1 F_10S082;301 87 3 F_05S177;1 24 1 F_50N306;1 52 1 F_10S082;1 9 1 F_05S177;301 101 3 F_10N307;1 52 1 F_25S082;301 111 3 F_10S177;201 72 2 F_05N307;1 53 1 F_25S082;1 13 1 F_10S177;1 24 1 F_10S307;1 52 1 F_35N083;1 119 1 F_10S177;301 101 3 F_70N310;1 50 1 F_35S083;301 122 3 F_55N180;1 66 1 F_60N312;1 50 1 F_35S083;1 11 1 F_50N180;1 66 1 F_15N312;1 53 1 F_30N085;301 120 3 F_15S180;201 73 2 F_05S312;1 59 1 F_30N085;1 111 1 F_15S180;1 25 1 F_75N313;1 56 1 F_30S085;1 121 1 F_20S180;201 73 2 F_65N318;1 58 1 F_05N087;1 10 1 F_20S180;1 26 1 F_05N318;1 53 1 F_05N087;201 111 2 F_50S180;1 76 1 F_00N318;1 93 1 F_00N087;1 10 1 F_55S180;1 77 1 F_55N319;1 53 1 F_05S087;201 72 2 F_10N183;1 77 1 F_55S319;201 75 2 F_05S087;1 10 1 F_05N183;1 77 1 F_25S320;301 110 3 F_05S087;301 106 3 F_05S183;1 26 1 F_50S320;202 121 2 F_10S087;301 107 3 F_10S183;201 72 2 F_40N321;1 52 1 F_10S087;201 72 2 F_10S183;1 26 1 F_40S321;301 110 3 F_10S087;1 10 1 F_60S185;201 76 2 F_20S322;301 98 3 F_45N088;201 71 2 F_60S185;1 77 1 F_60N323;1 53 1 F_45N088;1 70 1 F_65N186;1 27 1 F_15S323;301 98 3 F_40N088;201 72 2 F_25N186;1 26 1 F_35S323;301 110 3 F_40N088;1 11 1 F_20N186;1 25 1 F_70N324;1 52 1 F_40N088;301 104 3 F_15N186;1 32 1 F_10S324;301 98 3 F_50S088;1 11 1 F_65S186;1 94 1 F_30S325;301 103 3 F_25N089;1 120 1 F_65S186;201 77 2 F_25S327;301 98 3 F_35N090;301 121 3 F_45N188;1 66 1 F_55N328;1 52 1 F_35N090;1 108 1 F_10N188;1 25 1 F_20N328;1 53 1 F_35S090;1 11 1 F_05N188;1 24 1 F_40S328;301 103 3 F_35S090;301 101 3 F_10S188;1 25 1 F_55S328;201 75 2 F_10N093;301 121 3 F_50S188;1 76 1 F_05N329;301 103 3 F_10N093;1 120 1 F_00N189;201 64 2 F_15S329;301 103 3 F_05N093;1 120 1 F_00N189;1 24 1 F_65N330;1 1 1 F_00N093;1 120 1 F_05S189;1 93 1 F_65N330;1 3 1 F_00N093;301 121 3 F_15N191;1 25 1 F_35N330;1 52 1 F_05S093;201 72 2 F_20N192;1 24 1 F_35S330;301 103 3 F_05S093;301 107 3 F_25S192;1 74 1 F_75N332;1 1 1 F_05S093;202 102 2 F_40N194;1 28 1 F_75N332;1 3 1 F_10S093;1 80 1 F_10N194;1 24 1 F_30N332;1 1 1 F_15S094;301 121 3 F_05N194;201 64 2 F_30S332;301 103 3 F_15S094;1 120 1 F_05N194;1 24 1 F_25N333;201 58 2 F_20N097;1 15 1 F_00N194;201 64 2 F_25N333;1 53 1 F_20N097;301 98 3 F_00N194;1 24 1 F_60N334;1 3 1 F_55S097;1 77 1 F_45N195;1 26 1 F_60N334;1 1 1 F_55S097;202 106 2 F_60S196;201 75 2 F_20N334;201 56 2 F_55S097;201 94 2 F_60S196;1 70 1 F_20N334;1 1 1 F_10N098;1 17 1 F_50N197;1 27 1 F_05S335;1 1 1 F_05N098;1 15 1 F_35N197;1 27 1 F_55N337;1 1 1 F_05S098;1 15 1 F_15N197;1 25 1 F_55N337;1 3 1 F_10S098;1 15 1 F_65N198;1 28 1 F_55N337;201 58 2 F_30S098;201 64 2 F_20N198;1 25 1 F_70N339;1 4 1 F_05N099;301 104 3 F_25S198;201 74 2 F_27S339;1 1 1 F_05S099;201 72 2 F_25S198;1 71 1 F_15N340;1 3 1 F_05S099;202 108 2 F_55S199;201 75 2 F_65N342;1 4 1 F_05S099;301 105 3 F_55S199;1 76 1 F_40S342;1 1 1 F_10S099;301 104 3 F_10N200;1 25 1 F_60N344;1 4 1 F_25S101;1 110 1 F_05N200;201 72 2 F_25N345;1 4 1 F_60S101;201 76 2 F_05N200;1 25 1 F_25N345;301 86 3 F_65N102;201 68 2 F_00N200;201 72 2 F_25S345;1 3 1 F_65N102;1 15 1 F_00N200;1 25 1 F_50S345;1 3 1 F_20S103;1 108 1 F_10S200;1 27 1 F_50S345;1 1 1 F_00N104;1 104 1 F_40S201;1 67 1 F_55N346;1 4 1 F_05S104;1 104 1 F_15N203;1 35 1 F_50S348;201 59 2 F_10S104;1 104 1 F_35S203;1 94 1 F_40S349;1 4 1 F_30S104;1 105 1 F_20N204;1 28 1 F_45S349;1 3 1 F_15S106;1 104 1 F_20S204;1 29 1 F_45S349;201 62 2 F_20S109;201 74 2 F_50N205;1 28 1 F_75N351;1 7 1 F_60N111;1 18 1 F_25N205;1 70 1 F_75N351;301 122 3 F_15N111;1 13 1 F_10N205;1 32 1 F_25N351;1 4 1 F_45S111;1 98 1 F_05N205;1 27 1 F_25N351;301 107 3 F_15N112;201 63 2 F_00N205;1 27 1 F_20N351;1 4 1 F_15S112;201 64 2 F_05S205;201 68 2 F_70N353;1 6 1 F_65N114;1 17 1 F_05S205;1 28 1 F_70N353;301 122 3 F_65S114;1 67 1 F_05S205;202 119 2 F_65N354;1 6 1 F_65S114;201 76 2 F_30S205;201 74 2 F_65N354;301 106 3 F_05N115;201 67 2 F_30S205;1 26 1 F_65S354;1 3 1 F_00N115;201 64 2 F_60N207;1 28 1 F_60N355;1 6 1 F_05S115;201 64 2 F_60S207;201 75 2 F_60N355;301 105 3 F_10S115;201 68 2 F_60S207;1 26 1 F_55S355;1 4 1 F_15S117;201 63 2 F_55N208;1 28 1 F_60S355;1 3 1 F_45N119;1 17 1 F_40S208;1 67 1 F_50N356;1 6 1 F_25N119;1 17 1 F_35N210;1 80 1 F_50N356;301 98 3 F_25N119;201 68 2 F_20S210;1 29 1 F_50S356;1 4 1 F_20S121;1 17 1 F_45N211;1 27 1 F_50S356;201 59 2 F_30N123;1 13 1 F_25N211;1 27 1 F_55S356;201 63 2 F_15S123;1 18 1 F_10N211;1 29 1 F_25N357;1 6 1 F_65N126;1 13 1 F_05S211;1 29 1 F_20N357;301 87 3 F_45N126;1 17 1 F_10S211;1 29 1 F_20N357;1 5 1 F_20S127;1 80 1 F_45S211;201 75 2 F_05N357;1 5 1 F_15N129;1 15 1 F_45S211;1 28 1 F_00N357;1 5 1 F_15S129;1 94 1 F_30S212;1 28 1 F_05S357;1 5 1 F_30S129;1 13 1 F_15S214;201 73 2 F_20S357;1 5 1 F_35S130;1 13 1 F_15S214;1 29 1 F_25S357;1 5 1 F_25S131;201 68 2 F_10N217;1 32 1 F_30S357;1 5 1 F_25S131;1 13 1 F_05N217;1 29 1 F_35S357;1 5 1 PRODUCT TYPE: C1MIDRS PRODUCT CD CYCLE PRODUCT CD CYCLE PRODUCT CD CYCLE C1_30N009;301 115 3 C1_60N097;201 89 2 C1_75N209;1 41 1 C1_30N009;1 12 1 C1_60N097;2 97 1 C1_15N215;1 34 1 C1_15N009;1 14 1 C1_60S097;201 95 2 C1_00N215;201 88 2 C1_15N009;301 116 3 C1_60S097;1 22 1 C1_00N215;1 33 1 C1_00N009;1 14 1 C1_30N099;1 20 1 C1_15S215;201 89 2 C1_00N009;301 114 3 C1_30N099;201 61 2 C1_15S215;1 33 1 C1_15S009;301 115 3 C1_30N099;301 114 3 C1_45N223;1 37 1 C1_15S009;1 14 1 C1_30N099;2 97 1 C1_45S223;1 33 1 C1_30S009;1 14 1 C1_30S099;201 91 2 C1_45S223;201 78 2 C1_45N011;1 14 1 C1_30S099;1 20 1 C1_30N225;1 34 1 C1_45S011;1 12 1 C1_30S099;301 117 3 C1_30S225;1 34 1 C1_45S011;201 60 2 C1_30S099;2 96 1 C1_30S225;201 79 2 C1_60N014;301 115 3 C1_15N112;1 20 1 C1_15N232;1 37 1 C1_60N014;1 12 1 C1_15N112;201 61 2 C1_00N232;1 34 1 C1_60S014;1 16 1 C1_15N112;2 97 1 C1_15S232;1 34 1 C1_60S014;202 60 2 C1_00N112;201 88 2 C1_15S232;201 79 2 C1_75S023;201 85 2 C1_00N112;301 85 3 C1_15S232;301 113 3 C1_75S023;1 54 1 C1_00N112;1 19 1 C1_60N236;1 40 1 C1_15N026;301 115 3 C1_00N112;2 96 1 C1_60S236;1 37 1 C1_15N026;1 12 1 C1_15S112;1 20 1 C1_60S236;201 95 2 C1_15N026;2 112 1 C1_15S112;201 79 2 C1_30N243;1 40 1 C1_00N026;2 112 1 C1_15S112;301 115 3 C1_30S243;1 40 1 C1_00N026;301 114 3 C1_15S112;2 96 1 C1_30S243;201 90 2 C1_00N026;1 12 1 C1_75S113;201 85 2 C1_45N244;1 40 1 C1_15S026;201 90 2 C1_75S113;1 51 1 C1_45S244;1 40 1 C1_15S026;2 97 1 C1_45N117;201 79 2 C1_45S244;201 85 2 C1_15S026;1 12 1 C1_45N117;2 97 1 C1_45S244;301 113 3 C1_15S026;301 115 3 C1_45N117;1 21 1 C1_75S248;201 85 2 C1_30N027;2 112 1 C1_30N117;201 69 2 C1_75S248;1 48 1 C1_30N027;1 12 1 C1_30N117;1 21 1 C1_15N249;1 41 1 C1_30N027;201 60 2 C1_30S117;201 79 2 C1_00N249;1 40 1 C1_30S027;2 100 1 C1_30S117;2 96 1 C1_15S249;1 40 1 C1_30S027;1 14 1 C1_30S117;1 21 1 C1_75N254;1 48 1 C1_75N029;1 16 1 C1_45S117;201 78 2 C1_30N261;1 40 1 C1_75N029;2 69 1 C1_45S117;2 96 1 C1_30S261;201 79 2 C1_75N029;301 100 3 C1_45S117;1 21 1 C1_30S261;1 40 1 C1_45N032;301 116 3 C1_75N119;1 30 1 C1_60N263;1 41 1 C1_45N032;201 54 2 C1_60N125;1 21 1 C1_60S263;201 85 2 C1_45N032;1 12 1 C1_60S125;1 22 1 C1_60S263;1 41 1 C1_45S032;202 92 2 C1_60S125;201 95 2 C1_45N265;1 41 1 C1_45S032;1 14 1 C1_15N129;1 20 1 C1_45S265;1 40 1 C1_45S032;2 112 1 C1_15N129;301 112 3 C1_45S265;201 91 2 C1_45S032;201 95 2 C1_00N129;1 19 1 C1_15N266;1 41 1 C1_60N042;301 115 3 C1_00N129;301 112 3 C1_00N266;1 41 1 C1_60N042;1 16 1 C1_15S129;201 69 2 C1_15S266;1 41 1 C1_60S042;1 20 1 C1_15S129;1 19 1 C1_30N279;1 43 1 C1_60S042;3 97 1 C1_15S129;301 99 3 C1_30S279;1 41 1 C1_60S042;2 54 1 C1_30N135;301 114 3 C1_30S279;201 90 2 C1_60S042;202 57 2 C1_30N135;1 30 1 C1_15N283;1 43 1 C1_15N043;301 113 3 C1_30S135;301 117 3 C1_00N283;201 88 2 C1_15N043;201 57 2 C1_30S135;201 79 2 C1_00N283;1 43 1 C1_00N043;201 57 2 C1_30S135;1 21 1 C1_15S283;1 41 1 C1_15S043;201 57 2 C1_45N138;1 21 1 C1_45N286;1 47 1 C1_30N045;301 113 3 C1_45N138;301 115 3 C1_45S286;1 43 1 C1_30N045;201 57 2 C1_45S138;301 117 3 C1_45S286;201 91 2 C1_30S045;201 57 2 C1_45S138;201 92 2 C1_60N291;1 47 1 C1_45N053;1 16 1 C1_45S138;1 21 1 C1_60S291;1 47 1 C1_45N053;201 60 2 C1_15N146;301 116 3 C1_60S291;201 95 2 C1_45N053;301 116 3 C1_15N146;1 22 1 C1_75S293;202 85 2 C1_45S053;202 61 2 C1_00N146;201 61 2 C1_75S293;1 48 1 C1_45S053;301 116 3 C1_00N146;301 114 3 C1_30N297;1 47 1 C1_45S053;201 60 2 C1_00N146;1 22 1 C1_30S297;1 43 1 C1_15N060;201 89 2 C1_15S146;201 61 2 C1_30S297;201 90 2 C1_15N060;1 16 1 C1_15S146;301 117 3 C1_75N299;1 48 1 C1_15N060;202 92 2 C1_15S146;1 22 1 C1_15N300;1 47 1 C1_15N060;301 114 3 C1_60N153;1 31 1 C1_00N300;201 88 2 C1_00N060;201 57 2 C1_30N153;301 116 3 C1_00N300;1 47 1 C1_00N060;301 113 3 C1_30N153;1 22 1 C1_15S300;201 89 2 C1_00N060;202 60 2 C1_30S153;301 116 3 C1_15S300;1 47 1 C1_00N060;1 14 1 C1_30S153;1 22 1 C1_45N307;1 47 1 C1_15S060;201 57 2 C1_30S153;201 91 2 C1_45S307;201 91 2 C1_15S060;202 60 2 C1_60S153;1 22 1 C1_30N315;1 48 1 C1_15S060;1 16 1 C1_60S153;201 95 2 C1_30S315;201 90 2 C1_15S060;301 113 3 C1_75S158;201 96 2 C1_30S315;301 100 3 C1_30N063;301 113 3 C1_45N159;1 30 1 C1_30S315;1 47 1 C1_30N063;1 16 1 C1_45N159;301 99 3 C1_15N317;1 48 1 C1_30S063;201 69 2 C1_45S159;301 116 3 C1_15N317;301 99 3 C1_30S063;301 117 3 C1_45S159;1 22 1 C1_00N317;201 88 2 C1_30S063;1 16 1 C1_45S159;201 92 2 C1_00N317;301 100 3 C1_30S063;202 91 2 C1_15N163;1 31 1 C1_00N317;1 48 1 C1_75S068;201 96 2 C1_15N163;301 99 3 C1_15S317;201 89 2 C1_75S068;1 51 1 C1_00N163;201 89 2 C1_15S317;301 100 3 C1_60N070;201 89 2 C1_00N163;1 31 1 C1_15S317;1 48 1 C1_60N070;1 19 1 C1_00N163;301 116 3 C1_60N319;1 48 1 C1_60S070;201 85 2 C1_15S163;201 90 2 C1_60S319;201 95 2 C1_60S070;1 21 1 C1_15S163;301 117 3 C1_45N329;201 79 2 C1_75N074;201 69 2 C1_15S163;1 30 1 C1_45N329;2 60 1 C1_75N074;1 22 1 C1_75N164;1 37 1 C1_45N329;1 47 1 C1_45N074;301 113 3 C1_30N171;1 31 1 C1_45S329;202 85 2 C1_45N074;1 20 1 C1_30N171;301 99 3 C1_45S329;301 99 3 C1_45S074;201 92 2 C1_30S171;1 31 1 C1_30N333;201 79 2 C1_45S074;1 16 1 C1_30S171;301 99 3 C1_30N333;2 57 1 C1_45S074;301 96 3 C1_30S171;201 91 2 C1_30N333;1 2 1 C1_15N077;1 19 1 C1_60N180;1 30 1 C1_30S333;1 2 1 C1_15N077;201 78 2 C1_45N180;301 117 3 C1_30S333;301 100 3 C1_15N077;301 113 3 C1_45N180;1 30 1 C1_15N335;201 89 2 C1_00N077;301 114 3 C1_15N180;1 30 1 C1_15N335;1 2 1 C1_00N077;201 79 2 C1_15N180;301 99 3 C1_15N335;2 57 1 C1_00N077;1 16 1 C1_00N180;201 88 2 C1_15N335;301 100 3 C1_15S077;1 19 1 C1_00N180;301 117 3 C1_00N335;301 100 3 C1_15S077;301 114 3 C1_00N180;1 30 1 C1_00N335;1 2 1 C1_15S077;201 78 2 C1_15S180;201 90 2 C1_15S335;301 100 3 C1_30N081;301 115 3 C1_15S180;1 30 1 C1_15S335;1 2 1 C1_30N081;1 20 1 C1_15S180;301 99 3 C1_75N338;2 69 1 C1_30S081;1 20 1 C1_45S180;1 69 1 C1_75N338;1 14 1 C1_30S081;301 117 3 C1_45S180;301 99 3 C1_75S338;2 78 1 C1_30S081;201 91 2 C1_45S180;201 92 2 C1_75S338;202 97 2 C1_15N095;201 89 2 C1_60S180;1 33 1 C1_75S338;201 95 2 C1_15N095;301 115 3 C1_60S180;201 95 2 C1_75N344;301 100 3 C1_15N095;1 19 1 C1_30N189;1 31 1 C1_60N347;201 69 2 C1_15N095;2 112 1 C1_30S189;1 31 1 C1_60N347;1 14 1 C1_00N095;301 116 3 C1_30S189;201 91 2 C1_60N347;301 113 3 C1_00N095;201 89 2 C1_15N197;1 33 1 C1_60N347;2 54 1 C1_00N095;2 112 1 C1_00N197;201 88 2 C1_60S347;1 31 1 C1_00N095;1 19 1 C1_00N197;1 33 1 C1_60S347;201 60 2 C1_15S095;201 90 2 C1_15S197;201 90 2 C1_60S347;202 92 2 C1_15S095;301 117 3 C1_15S197;1 33 1 C1_45N350;301 88 3 C1_15S095;1 19 1 C1_45N202;1 31 1 C1_45N350;1 12 1 C1_15S095;2 97 1 C1_45S202;1 31 1 C1_45S350;1 2 1 C1_45N096;1 20 1 C1_45S202;201 92 2 C1_45S350;201 60 2 C1_45N096;201 61 2 C1_75S203;201 84 2 C1_30N351;301 88 3 C1_45N096;2 97 1 C1_75S203;1 48 1 C1_30N351;1 12 1 C1_45N096;301 114 3 C1_30N207;1 33 1 C1_30S351;1 2 1 C1_45S096;1 19 1 C1_30S207;1 33 1 C1_15N352;301 88 3 C1_45S096;301 114 3 C1_30S207;201 91 2 C1_15N352;1 2 1 C1_45S096;2 97 1 C1_60N208;1 37 1 C1_00N352;1 2 1 C1_45S096;201 92 2 C1_60S208;1 34 1 C1_15S352;1 2 1 C1_60N097;1 21 1 C1_60S208;201 95 2 PRODUCT TYPE: C2MIDRS PRODUCT CD CYCLE PRODUCT CD CYCLE PRODUCT CD CYCLE C2_30N026;1 34 1 C2_60N093;301 118 3 C2_30S232;201 81 2 C2_30N026;301 84 3 C2_60S093;1 54 1 C2_30S232;1 43 1 C2_30S026;1 37 1 C2_60S093;202 82 2 C2_00N234;1 43 1 C2_30S026;201 84 2 C2_30N129;201 83 2 C2_00N234;201 81 2 C2_30S026;202 81 2 C2_30N129;1 34 1 C2_60N273;2 61 1 C2_00N028;301 96 3 C2_30N129;301 84 3 C2_60S273;1 54 1 C2_00N028;201 83 2 C2_30S129;301 118 3 C2_60S273;202 83 2 C2_00N028;1 37 1 C2_30S129;201 82 2 C2_60S273;201 82 2 C2_60N033;301 118 3 C2_30S129;1 37 1 C2_30N284;1 51 1 C2_60N033;1 43 1 C2_00N131;201 81 2 C2_30N284;2 61 1 C2_60N033;2 61 1 C2_00N131;1 34 1 C2_30S284;201 82 2 C2_60N033;202 84 2 C2_00N131;301 118 3 C2_30S284;202 81 2 C2_60N033;201 83 2 C2_60N153;202 82 2 C2_30S284;1 51 1 C2_60S033;202 83 2 C2_60N153;1 51 1 C2_00N286;201 83 2 C2_60S033;201 82 2 C2_60N153;301 118 3 C2_00N286;1 51 1 C2_60S033;1 54 1 C2_60N153;2 61 1 C2_60N333;2 51 1 C2_30N078;202 84 2 C2_60S153;1 54 1 C2_60N333;301 118 3 C2_30N078;1 33 1 C2_60S153;201 82 2 C2_60N333;201 81 2 C2_30N078;301 119 3 C2_30N181;1 43 1 C2_60S333;202 83 2 C2_30N078;201 83 2 C2_30N181;301 112 3 C2_60S333;201 82 2 C2_30S078;202 81 2 C2_30S181;1 37 1 C2_60S333;1 69 1 C2_30S078;301 96 3 C2_30S181;201 81 2 C2_30N335;2 51 1 C2_30S078;1 37 1 C2_30S181;301 118 3 C2_30N335;301 118 3 C2_30S078;201 84 2 C2_00N183;1 34 1 C2_30N335;302 112 3 C2_00N080;1 30 1 C2_00N183;201 81 2 C2_30N335;303 90 3 C2_00N080;202 83 2 C2_00N183;301 118 3 C2_30S335;201 82 2 C2_00N080;201 84 2 C2_60N213;1 54 1 C2_30S335;301 119 3 C2_00N080;301 92 3 C2_60S213;202 82 2 C2_30S335;202 81 2 C2_60N093;202 83 2 C2_60S213;1 54 1 C2_00N337;302 118 3 C2_60N093;1 51 1 C2_30N232;1 43 1 C2_00N337;2 51 1 PRODUCT TYPE: C3MIDRS PRODUCT CD CYCLE PRODUCT CD CYCLE PRODUCT CD CYCLE C3_14N060;1 78 1 C3_14S060;201 84 2 C3_14N300;301 119 3 C3_14N060;301 119 3 C3_14N180;301 119 3 C3_14N300;201 84 2 C3_14N060;201 85 2 C3_14N180;1 69 1 C3_14N300;1 78 1 C3_14S060;1 78 1 C3_14S180;1 78 1 C3_14S300;1 78 1